Search found 205 matches
- Wed Nov 18, 2020 5:49 pm
- Forum: Silencersmithing Forum
- Topic: Form 1 30cal planning stages
- Replies: 2
- Views: 2018
Re: Form 1 30cal planning stages
SPC doesn't make a 60° Pro cone. It is either 60° or a Pro. Skip the DHC on the 60° and it isn't even possible on the Pro. Not enough meat on the tip of the cone. Much better cones that would work for both cartridges, but you'd have to put up with some first round pop with the BLK if you built an al...
- Fri Sep 11, 2020 12:11 am
- Forum: Silencer Talk
- Topic: First range report on my Form1 build.
- Replies: 18
- Views: 3196
Re: First range report on my Form1 build.
Are they HIT's flat washer looking things or their actual cone shaped "spacers"? If cone shaped, do something with them. Washers...well, sorry.
- Tue Sep 08, 2020 5:17 pm
- Forum: Silencersmithing Forum
- Topic: Form-1 TI suppressor new build ideas
- Replies: 2
- Views: 2116
Re: Form-1 TI suppressor new build ideas
Head over to the form1suppressor.boards.net and sign up.
Do some searching and reading. When you think you have it figured out, or need to ask a question, keep reading.
Do some searching and reading. When you think you have it figured out, or need to ask a question, keep reading.
- Thu Jul 02, 2020 10:48 pm
- Forum: Silencersmithing Forum
- Topic: What would cause inaccuracy when hot?
- Replies: 13
- Views: 4502
Re: What would cause inaccuracy when hot?
Mirage from the heat of the suppressor?
- Wed Jul 01, 2020 11:21 pm
- Forum: Silencersmithing Forum
- Topic: Another Solvent Trap Vendor Shut Down ?
- Replies: 3
- Views: 2996
Re: Another Solvent Trap Vendor Shut Down ?
Shopify pulled the plug on them a few days ago.
- Mon Jun 01, 2020 11:28 pm
- Forum: Silencersmithing Forum
- Topic: Drilling K cups and cones
- Replies: 6
- Views: 4133
Re: Drilling K cups and cones
I make drilling jigs for all sorts of cones. Easiest to get ahold of me on the form1suppressor.boards.net. Sign up, shoot me a message and let me whose cones/size/shape and maybe even include a picture, especially the K-Cups. Use imgbb.com for the photo hosting. About the only site that likes me.
- Tue May 05, 2020 7:24 pm
- Forum: Silencersmithing Forum
- Topic: 9mm design feedback requested
- Replies: 3
- Views: 2032
Re: 9mm design feedback requested
I like what you are doing!! I was trying to buy a couple K-Cup "filters" off of eBay to make drilling jigs for, but they were snagged by Customs. Couple suggestions. Make the jigs slightly undersized. Warm up one of the cones to where it is just warm enough to deform the plastic, but not t...
- Tue Apr 21, 2020 10:33 pm
- Forum: Silencer Talk
- Topic: Solvant can Durability
- Replies: 3
- Views: 1676
Re: Solvant can Durability
I hope I didn't catch a virus clicking on that link.
If you think it is 7075....
Cheap Chinese Can Experiment. Search for that on AR15.com.
If you think it is 7075....
Cheap Chinese Can Experiment. Search for that on AR15.com.
- Sat Apr 18, 2020 7:39 pm
- Forum: Silencer Talk
- Topic: Cutting Up My Cans... Or selling them
- Replies: 21
- Views: 5605
Re: Cutting Up My Cans... Or selling them
Glad to help.
- Thu Apr 16, 2020 12:24 am
- Forum: Silencer Talk
- Topic: Cutting Up My Cans... Or selling them
- Replies: 21
- Views: 5605
Re: Cutting Up My Cans... Or selling them
imgbb.com is free and doesn't require an account. Once you upload the pic, use the pull down menu and select BBCode Full Linked. C&P that address in your reply and the pic will show up.
- Thu Apr 16, 2020 12:21 am
- Forum: Silencersmithing Forum
- Topic: Sub $1k lathe including shipping 8x16 with 5” chuck 1.5” pass thru
- Replies: 90
- Views: 47812
Re: Sub $1k lathe including shipping 8x16 with 5” chuck 1.5” pass thru
Yeah, I'd still take the motor. Shoot me a PM an I'll pay shipping if you're willing to get rid of it. My mill gets used close to every other day. Granted, 95% of it is just drilling small holes and running a spiral tap, but I have been very pleased with it for everything else I have needed it to do.
- Wed Apr 08, 2020 10:15 pm
- Forum: Silencersmithing Forum
- Topic: Form 1 builder.com
- Replies: 13
- Views: 7306
Re: Form 1 builder.com
All aluminum build wouldn't be what I would want for a possible high rate of fire can. Especially low grade 6061.
- Fri Apr 03, 2020 6:32 pm
- Forum: Silencersmithing Forum
- Topic: First Form 1 Design
- Replies: 39
- Views: 17610
Re: First Form 1 Design
With the ASR tubes, you don't need extra blast chamber material. If you need to move the cone further away from your brake, you can drop the appropriate spacer in before your first cone.
- Sun Mar 29, 2020 11:45 pm
- Forum: Silencersmithing Forum
- Topic: Questions about drilling titanium and SS
- Replies: 9
- Views: 2783
Re: Questions about drilling titanium and SS
I have used cheap drill bits from HF that were coated and rather expensive cobalt bits. Both did the job if care is taken. I always recommend the cobalt because they will take a little more abuse.
MMW's endcap doesn't have dimples/centering marks.
MMW's endcap doesn't have dimples/centering marks.
- Tue Mar 17, 2020 2:27 pm
- Forum: Legal and Political
- Topic: Politicians Push For All New Firearms Have Suppressors
- Replies: 4
- Views: 3795
Re: Politicians Push For All New Firearms Have Suppressors
Gotcha. I saw the number, but thought it was in reference to a docket number or something because I didn't know what WSJ was.
- Mon Mar 16, 2020 6:14 pm
- Forum: Legal and Political
- Topic: Politicians Push For All New Firearms Have Suppressors
- Replies: 4
- Views: 3795
Re: Politicians Push For All New Firearms Have Suppressors
Is someone pulling your leg, or are you pulling ours?
- Mon Mar 16, 2020 6:11 pm
- Forum: Silencersmithing Forum
- Topic: First Form 1 Design
- Replies: 39
- Views: 17610
Re: First Form 1 Design
Leaving one spacer a little (.020" or so) long won't hurt. After firing a few shots, check endcap tightness and repeat for how many rounds you feel comfortable with, that you can't tighten the endcap any more. Then you can remove what little bit of the long spacer you need to get the cap to sit...
- Mon Mar 16, 2020 6:03 pm
- Forum: Silencersmithing Forum
- Topic: Form 1 build material sourcing?
- Replies: 29
- Views: 12382
Re: Form 1 build material sourcing?
I had a customer send me one a while back. I just checked the skirt and it is .038" thick. After looking at it, I see why they went thinner. The I.D. of the skirt on the one I have is smaller than the O.D. at the base of the coned section. No way this one would have stacked onto another one. Th...
- Mon Mar 09, 2020 6:30 pm
- Forum: Silencersmithing Forum
- Topic: Form 1 build material sourcing?
- Replies: 29
- Views: 12382
Re: Form 1 build material sourcing?
Which cones did you get from STD?
- Mon Mar 09, 2020 6:29 pm
- Forum: Silencer Talk
- Topic: Silencer on a gas delayed blowback pistol?
- Replies: 33
- Views: 18217
Re: Silencer on a gas delayed blowback pistol?
That sucks to hear. What happened? Neither of them are salvageable? Pics?
- Sun Mar 08, 2020 2:44 pm
- Forum: Silencersmithing Forum
- Topic: Aegis-Products Out ofBusiness ?
- Replies: 2
- Views: 3490
Re: Aegis-Products Out ofBusiness ?
He went MIA on the 4th on all sites! Removed accounts, deleted posts and hasn't logged on since. Another company saying he was shut down.
- Sun Mar 01, 2020 9:55 pm
- Forum: Silencersmithing Forum
- Topic: Practice material
- Replies: 8
- Views: 4075
Re: Practice material
Get some cheap 6061 round bar and have some fun. Won't be anything like 17-4 or Ti, but you'll get the jist of threading, turning, boring and everything else that goes with the process and only risk pennies on the dollar. When it comes down to the real thing, go slow and check your work frequently. ...
- Fri Feb 28, 2020 10:29 pm
- Forum: Silencersmithing Forum
- Topic: Would like help making K baffles
- Replies: 7
- Views: 4307
Re: Would like help making K baffles
Plenty of images on your favorite search engine.
- Fri Feb 28, 2020 10:27 pm
- Forum: Silencersmithing Forum
- Topic: Caliber
- Replies: 4
- Views: 3097
Re: Caliber
Yes, it would. How effective is the question.
- Thu Feb 27, 2020 8:22 am
- Forum: Silencer Talk
- Topic: Silencer on a gas delayed blowback pistol?
- Replies: 33
- Views: 18217
Re: Silencer on a gas delayed blowback pistol?
That certainly looks like it would be an easy barrel replacement job.