Will this be at the open house? What is the date for September?

I clean my 51T and I clean all around in the attachment end of the SDN. However, the 51T individual teeth receive the least of my cleaning attention.

What caliber is it?

Would a EFK FNS-9 barrel with metric threads have the ability to properly shoulder?
thanks,

I did not know that about the metric threads. Also, I sent the LW, EFK barrels and the piston/booster to Liberty. As stated they were super on the core replacement, but no mention of the shouldering or lack there of. However, I will look into the EFK situation. Also, the shouldering is easy to deter...

There is a shoulder difference between the EFK and Lone Wolf (LW) barrels, the outside diameter of the EFK is 0.500 inch and the LW is 0.569 inch. Threads on both are the same. Thus the piston of the Infiniti and the Osprey both thread until the barrel tip touches the non-thread inside of the piston...

THANKS, can you tell anything from my other post?

viewtopic.php?f=77&t=125484

Yes it happened, 8/20. Returned from Liberty 9/2, no charge new mono-core. Not sure how, plated 147 gr bullets, VV N320, 3.7 gr, EFK Fire Dragon Barrel, FNS 9. It is possible the recoil booster was part of the cause, but not sure, but two rounds went down the pipe and the pictures tell the results. ...

You have made a nice unit.
What camera do you use? The sound is good, seems close to actual, what software do you edit with?
Take an oven mitt, until you find a wrapper you like.

Nice parable, isn't there a historic progression that is summarized, "....for the want of a nail the battle was lost"?
However, 3 inch with can comes out to a nice overall length...

Yes

Here is a video of it on a Savage Mark 2 with Remington subsonics. The mono-core cleans up with time and attention. I put CLP on the core over night, then brush and scrap with a small screwdriver. Its a great can !!!! http://vid1293.photobucket.com/albums/b596/paper99/libertytrimPICT0001_zps80374bc0...

This is a Form 1 build on a Savage Mark 2, 22 lr.

http://vid1293.photobucket.com/albums/b ... 7e21c9.mp4

Take a look in the Handloading section.

G26 platform, 4 inch Lonewolf barrel
Magneto Speed Chronograph
6 round sample
CCI 500 primers
3.8 gr VV N340
OAL 1.142
147 GR Extreme Plated RN
Cycles, not crimped, no key holes.

V MAX = 976
V MIN = 945
V AVE = 961

What about electronic copies? Various tablets are 7 inch or bigger and should display the document nicely.

Accurate No 7 gives me big blow back on 3 suppressed platforms, 147 gr.
VV N320 does not, 147 gr.

To me, that short Ruger barrel looks prone to baffle strike.

Do slugs work with choke tubes? THANKS.

Probably about 4 weeks.

I think the Delrin ones can found online. I am guessing that DIY is cheaper.

Well, over 100 rounds and it cycles the G26 with the Lonewolf. Loads are VV N320, 3.8 grains, 147 gr, round nose, Osprey 9 on the end of the Lonewolf.

Well it has been a year, how do they shoot?

Yes, it has a recoil booster and I am working on the 200 rounds, I had the same thought.

I tried the G26 with a Lonewolf threaded barrel, it does not cycle with a Infiniti attached.
It cycles far enough to reset the trigger, but the spent brass stays put in the chamber.
147 gr handload, Accurate 7, 6.0 grains.
Any ideas, suggestions? Thanks.