Page 2 of 3

Re: Building a 22/24 integral can

Posted: Wed Jan 15, 2014 4:30 pm
by unclemoak
I don't have too much to update. Right before the holidays was kind of crazy for my because I unfortunately totaled my car and had a little bit of a mad dash to find a new one.

Image


Other than that slight setback, I was able to find a source of barrels. Someone on Rimfire Central tipped me off that Volquartzen usually has take off barrels, so I was able to get a pile of them from them @ $35 a piece, compared the the $80 I paid for the two from Clark Custom Guns.

Image

The next steps will be finalizing a receiver design for the testing, then trying to find some .22 ammo, so if anyone knows of any sources of .22 ammo, please PM me. I'll need around 500rds of maybe 6-7 different brands for my testing.

Re: Building a 22/24 integral can

Posted: Thu Jan 16, 2014 1:00 pm
by Baffled
Cool project! Unfortunately, .22 ammo is just ridiculous right now. I'm still running off my stash of CCI Blazer I picked up for $8 a brick way back when! Plus an assortment of subsonic stuff.

This .22 ammo supply issue is just insanity. The price of rimfire is now approaching centerfire!

Re: Building a 22/24 integral can

Posted: Thu Jan 16, 2014 8:16 pm
by Tony M.
Baffled wrote: This .22 ammo supply issue is just insanity. The price of rimfire is now approaching centerfire!
Yeah, I reload, so it's cheaper for me to shoot the .45 than the .22 :shock:

Re: Building a 22/24 integral can

Posted: Tue Apr 01, 2014 7:09 pm
by unclemoak
Today I spend a little bit of time putting together my testing plan. I want to get an idea of what barrel length bullets will stay sub-sonic. My plan is to start at the factory length barrel and cut it down by 0.1" until it's 2.0" in length and record a number of variables along the way using a couple different kinds of ammo.

Image


I also called up Ruger today to order a handful of ejectors and rivets for the new receivers I'm going to machine for the test barrels. It was about $50 for 10 of each, which should give me a few extra in case I mess up any.


Tore out the LCI, because frankly, who needs that pile of crap?
Image


The next order of business was to take the MK II prints that I was able to find online and turn them into a solid model and print for the receivers that I'm going to make.

This is the print that I started with
Image


And the horrendous looking receiver it yeilds.
Image


Changed the ejection port a bit to be a little better looking.
Image


All the cuts in the bottom.
Image


Wire frame to see all the innards.
Image


Next up will be to find some material to make the receiver blanks out of, find the appropriate take to cut the barrel threads, and then hopefully start making chips.

Re: Building a 22/24 integral can

Posted: Wed Apr 02, 2014 9:52 am
by Hatchetjoe
Any plans on making a left side eject version?

Re: Building a 22/24 integral can

Posted: Wed Apr 02, 2014 10:58 am
by MCKNBRD
[right click] drawings...

And saved.

:D

Got another project for the lathe/mill now...

Byrdman

Re: Building a 22/24 integral can

Posted: Wed Apr 02, 2014 6:32 pm
by unclemoak
Hatchetjoe wrote:Any plans on making a left side eject version?
No plans currently. I suppose it wouldn't be too hard. The receiver is the easy part, making a new bolt would be slightly more involved.
MCKNBRD wrote:[right click] drawings...

And saved.

:D

Got another project for the lathe/mill now...

Byrdman
The receiver should be a breeze with a bridgeport and a rotary table/tail stock.

Re: Building a 22/24 integral can

Posted: Thu Apr 03, 2014 7:04 am
by Hatchetjoe
I was thinking maybe the bolt would just need a new slot to clear the left side ejector, and rework for the extractor on the left, not a completely new bolt, but admittedly I haven't looked at this too hard yet.

Re: Building a 22/24 integral can

Posted: Thu Apr 03, 2014 7:39 pm
by daviscustom
OK Hatchetjoe, my curiosity has gotten the better of me....it's a pistol......Why do you care which side it ejects on? I get that maybe you are a lefty, but it is held out in front of you with both or either hand.....I don't understand the need for it to eject on the left.

Re: Building a 22/24 integral can

Posted: Thu Apr 03, 2014 11:04 pm
by whiterussian1974
daviscustom wrote:OK Hatchetjoe, my curiosity has gotten the better of me....Why do you care which side it ejects on? I get that maybe you are a lefty, but it is held out in front of you with both or either hand.....I don't understand the need for it to eject on the left.
I can't speak for Hatchet.

When it comes to firing a "defensive" pistol strong-handed, it is canted slightly outward and held with wrist against the junction of ribs and chest. The ejecting brass might jam when bouncing against the body and then rebounding toward ejection port.

But you're right. Why bother if it's a .22? Who's going to tuck the pistol against their body? The action cycling the bolt creates too great of a jam/pinch hazard in and of itself.

I'm also interested in Hatchetjoe's answer.

Re: Building a 22/24 integral can

Posted: Fri Apr 04, 2014 5:11 am
by gunny50
daviscustom wrote:OK Hatchetjoe, my curiosity has gotten the better of me....it's a pistol......Why do you care which side it ejects on? I get that maybe you are a lefty, but it is held out in front of you with both or either hand.....I don't understand the need for it to eject on the left.

Who says one has to use it as a pistol receiver?
Right hand ejected brass flies in front of your view, sometimes that is just not what a customer wants…
Pistol or rifle does not matter in that case.


Gunny

Re: Building a 22/24 integral can

Posted: Fri Apr 04, 2014 9:11 am
by Hatchetjoe
I like Gunny's thought process. However I was just thinking about shooting double handed one in the left hand and one in the right. As far as pistols and defensive weapon I think a suppressed .22 come under the heading of offensive pistol.

Re: Building a 22/24 integral can

Posted: Fri Apr 04, 2014 10:56 am
by whiterussian1974
Hatchetjoe wrote:I like Gunny's thought process. However I was just thinking about shooting double handed one in the left hand and one in the right. As far as pistols and defensive weapon I think a suppressed .22 come under the heading of offensive pistol.
CIA and Mafia have always loved them for Offensive use. :twisted:
But larger surface area of .40 and .45 are preferred for defensive use.
An old saying from the 1970-80's: "9mm is Mankiller, .45 is Manstopper." I've seen this borne out many times. Seen people shot 4 or 5 times w .45 and still live. !?! But they sure dropped quick and didn't get up until EMTs carried them away.

Re: Building a 22/24 integral can

Posted: Fri Apr 04, 2014 12:06 pm
by unclemoak
A post on another forum and this video I watched (at the 1:00 mark) a while ago:

https://www.youtube.com/watch?v=sBHOay8TAiI


got me to do a little thinking. Instead of trying to squeeze everything into a small 1" OD piece of tubing, why not just fit up the frame to a large diameter receiver?

This is a 1.25" OD piece of tubing that I had laying around.

Image


It might cause me to have to make some changes to the mechanicals, but for the increased volume, I think it'll probably be worth it.

Re: Building a 22/24 integral can

Posted: Fri Apr 04, 2014 5:04 pm
by daviscustom
gunny50 wrote:
daviscustom wrote:OK Hatchetjoe, my curiosity has gotten the better of me....it's a pistol......Why do you care which side it ejects on? I get that maybe you are a lefty, but it is held out in front of you with both or either hand.....I don't understand the need for it to eject on the left.

Who says one has to use it as a pistol receiver?
Right hand ejected brass flies in front of your view, sometimes that is just not what a customer wants…
Pistol or rifle does not matter in that case.


Gunny
Didn't mean that there wasn't a good reason to do it, I was just curious what his reason was. :wink:

Unclemoak....if you get too carried away it's gonna start to look like a flare gun, but that would certainly give you more volume to play with. Maybe that would allow you to shorten the suppressor without losing performance. 1 1/8" tubing is an option as well.

Re: Building a 22/24 integral can

Posted: Mon Apr 07, 2014 5:28 pm
by unclemoak
Parts are starting to roll in.


On Friday my ejectors and rivets came in from Ruger.
Image


And the UPS man just dropped off the steel for the test receivers.

Image


It wasn't too easy to find correctly sized tubing in anything but aluminum. I could find 1.0" OD x .760" ID, but thought that would be a little sloppy and have a negative affect on accuracy, so I found steel tubing from one of my favorite metal vendors, (http://www.speedymetals.com/) which just happens to be right up the road, in 1.0" OD x 0.624" ID. Because of that I'll have to ream it out most likely with a .749" reamer, then hone it the rest of the way to get it to .750".

Image

Image

Re: Building a 22/24 integral can

Posted: Tue Apr 08, 2014 8:20 pm
by unclemoak
This is my new thought on going to a sleeve over the receiver design, which is still very conceptual at this point. I would essentially be taking my piece of 1.0" OD x .75" ID material for the receiver and cutting the barrel threads in it, then pressed it into a 1.125" OD x 0.995" ID tube. Then I would finish doing the rest of the machining on the receiver.

Image

Re: Building a 22/24 integral can

Posted: Tue Apr 08, 2014 11:58 pm
by whiterussian1974
You could still add sumps between bore chambers. Mill out sections at top and bottom of core that boreline chambers bleed into. This creates extra volume and valves that delay release of stagnant gas back into Boreline Chambers.

There have been many threads here showing this. I don't have time to scan through them though.

These "69" chambered monocores are another option.
ImageImageImageImage

Re: Building a 22/24 integral can

Posted: Wed Apr 09, 2014 6:04 am
by unclemoak
whiterussian1974 wrote:You could still add sumps between bore chambers. Mill out sections at top and bottom of core that boreline chambers bleed into. This creates extra volume and valves that delay release of stagnant gas back into Boreline Chambers.

There have been many threads here showing this. I don't have time to scan through them though.

These "69" chambered monocores are another option.
ImageImageImageImage

That's the plan. That core was just an initial mock up.

Re: Building a 22/24 integral can

Posted: Tue Apr 15, 2014 6:35 pm
by unclemoak
As I mentioned before, I wasn't able to locate tubing that was exactly what I needed, so I had to bore out the 0.624" ID tubing to close to the right size. I had a little bit of time this evening, so I faced and drilled out the tubing to 47/64ths (just under the final 3/4" size). Later I'll ream it to 0.75" and run a hone through it to clean up the surface.

Image


You can see a decent amount of material was removed.

Image


Since I didn't have an +8" long drill bit, I had to drill the tube from both ends. If you look closely, you can see a slight step in the middle. That will come out when the tubes get reamed and honed later.
Image


Short video clip of the drilling.
Image

Re: Building a 22/24 integral can

Posted: Thu Apr 17, 2014 4:56 pm
by daviscustom
whiterussian1974 wrote:You could still add sumps between bore chambers. Mill out sections at top and bottom of core that boreline chambers bleed into. This creates extra volume and valves that delay release of stagnant gas back into Boreline Chambers.

There have been many threads here showing this. I don't have time to scan through them though.

These "69" chambered monocores are another option.
ImageImageImageImage

I have heard that one works pretty good. :wink:

If you go that route with the smaller double blast chambers, make sure you leave plenty of wall thickness between them. We thinned out that wall in the CNC version and had issues with that divider wanting to bow forward on the unsupported edges and lock the tube in place.......never had any issues with the original that is pictured.

Re: Building a 22/24 integral can

Posted: Sat Apr 26, 2014 6:09 am
by LawBob
Bendersquint wrote:
unclemoak wrote:
Dr.K wrote:Plenty of people have made integral cans before too, but I don't think I've seen anyone make a monolithic integral can before similar to the Gemtech Oasis and when you're young, single, and have way too much time on your hands, why not?
There have been a few of them built. I recall seeing one in all 3 flavors......aluminum, titanium and stainless steel. The Ti one even had a ported barrel!
He said monolithic. Anything other than factory receiver metal is impossible.

Never mind I see he abandoned that idea

Re: Building a 22/24 integral can

Posted: Sat Apr 26, 2014 8:31 am
by Baffled
No pics... bandwidth exceeded... :(

Re: Building a 22/24 integral can

Posted: Wed May 14, 2014 2:46 pm
by rancilio
Keep it coming uncle! Thanks.

Re: Building a 22/24 integral can

Posted: Sun May 25, 2014 8:50 pm
by unclemoak
rancilio wrote:Keep it coming uncle! Thanks.
Did I mention I get easily distracted?

In completely unrelated news, I made this lightweight carrier the other day. Just has to go to heat treat,blast, and then to coater for QPQ.
Image