Page 1 of 1
WTK: AAC 51T ACME thread pitch once and for all!
Posted: Wed Aug 27, 2014 10:55 pm
by 1968firebirdguy
Hey guys, hopefully one of you can help me out.
I have searched high and low but I haven't been able to find a solid be all end all answer.
what size is the ACME thread pitch on the 51T flash hider?? is it 8 tpi , 7 tpi , 7.5tpi????
any one!! my google fu seems to be lacking at the moment
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Thu Aug 28, 2014 5:05 am
by john.t.little1
i seem to remember bender saying its close to 9.5 if i remember correctly…
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Sun Aug 31, 2014 8:06 pm
by 1968firebirdguy
135 views and still no solid answer?
come on guys some one has to know for sure
if I had the means of measuring the threads I would figure it out myself but I don't have the the right equipment to do it correctly.
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Sun Aug 31, 2014 8:30 pm
by john.t.little1
Ask this guy
sizulku wrote:
Hi Gunny,
Which one is perform better, using the same spacing length or different spacing length?
I build my 556 nato can based on AAC M4-2000 above. Its 2" diameter and 10" long. Nine 60-degree cones baffle. Bore is 0.252" and all spacer is 0.5".
I shot side-by-side at the range with AAC M4-2000 and unable to tell difference the sound of this can compare to AAC M4-2000 except the size and weight. I'm not happy with this result. the good thing of this can is I don't get POI shift.
Any suggestion?
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Sun Aug 31, 2014 9:06 pm
by 1968firebirdguy
John
Thanks for the reply , I did infact try asking him and I never got a response. He said he was going to check his notes and he never got back me in the post.
I may try to find one of those little fold out thread combs in ACME and take it to the flash hider I have , I have heard many different sizes from people, I know the YHM phantom threads are 8tpi and it looks really close to the AAC so I was figuring it's gotta be close to that.
Thank you again for the help
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Sun Aug 31, 2014 9:33 pm
by john.t.little1
You're welcome. I do believe bender knows and I seem to remember him saying it's 9.5ish
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Wed Oct 08, 2014 2:10 pm
by sizulku
Hi Gents.
Sorry for delays. I use metric thread number 4 as shown on the picture below.
this is the machine
metric thread pitch list
my setup
making aac nut
result
hope this help.
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Wed Oct 08, 2014 6:49 pm
by john.t.little1
Not worthy… thank you Sir you have done a great service for all..
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Wed Oct 08, 2014 8:45 pm
by ken226
so, a 4mm pitch makes kit 6.35 tpi. I thought 9.5 would be a little odd, most manual lathes wouldn't be able to cut a 9.5 pitch i wouldnt think. I'm sure it wouldn't be a problem for a CNC.
A 4mm pitch should be doable on most machines.
Re: WTK: AAC 51T ACME thread pitch once and for all!
Posted: Thu Jan 02, 2020 4:44 pm
by Zero99z
Sorry to hijack the thread, but if someone has the acme thread pattern for the AAC Cyclops it would be much appreciated.