After a 10 rd mag, the suppressor needs re-tightened. Ready to Cerakote but haven't had this problem before. Should I make a facing cut leaving only a small shoulder around the threaded hole?
Or am I doing it wrong & need to leave the wave/spring washer in place on the 22/45?
Endcap won't stay tight
Endcap won't stay tight
--------------------------------------
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
Re: Endcap won't stay tight
Why not just a drop of loctite?
300 blackout form 1: http://www.silencertalk.com/forum/viewtopic.php?f=10&t=137293
5.56 form 1:
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=141800&p=955647#p955647
5.56 form 1:
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=141800&p=955647#p955647
Re: Endcap won't stay tight
loctite or plumbing tape
varying amounts of clean up with either
varying amounts of clean up with either
http://www.youtube.com/watch?v=BDtd2jNIwAU MUSAFAR!
http://www.youtube.com/watch?v=8CrOL-ydFMI This is Water DavidW
Complete Form 1s http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.youtube.com/watch?v=8CrOL-ydFMI This is Water DavidW
Complete Form 1s http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
Re: Endcap won't stay tight
I would try an O-Ring set down all the way against the barrel thread relief. It would crush and add a bit of friction, although it may not last for a lot of removal cycles. Fortunately, you can buy them by the bag! My hunch is that your end cap thread major diameter is a hair oversize, and there is not much to be done about that besides cutting a new one.
-
- Silent But Deadly
- Posts: 1204
- Joined: Fri Oct 11, 2013 3:09 pm
Re: Endcap won't stay tight
Is that some sort of barrel threaded adapter over either a skinny barrel liner or a barrel end that's been turned down to fit it? Can't quite make out what I'm seeing there. If it's an end cap on the gun itself, what about having one made with a slightly larger thread OD, just a bit fatter so the suppressor threads on snug? Of course if the threaded portion with the 4 holes in it isn't just a small part that's not going to work... but it really seems like it's a soda straw barrel with some sort of threaded adapter.
- T-Rex
- Silent But Deadly
- Posts: 1865
- Joined: Wed Oct 29, 2014 3:38 pm
- Location: CT - The AntiConstitution State
Re: Endcap won't stay tight
I would try taking a facing cut, on the suppressor adapter, but leave a small shoulder in place.
The materials are most likely heating up and pushing each other apart.
A small shoulder should help alleviate some expansion.
The materials are most likely heating up and pushing each other apart.
A small shoulder should help alleviate some expansion.
Completed Builds www.silencertalk.com/forum/viewtopic.php?t=79895
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Re: Endcap won't stay tight
a_canadian- looks to me like one of the Ruger Lite models of their 22 pistol, aluminum sleeve over a tensioned thin steel barrel.
OP, I had a similar problem with a form1 .223 can, and a stout wave washer fixed it. Haven't had the same issue with my 22/45, though.
OP, I had a similar problem with a form1 .223 can, and a stout wave washer fixed it. Haven't had the same issue with my 22/45, though.
Re: Endcap won't stay tight
22/45 Lite. I'll try w/ wave washer installed. For some reason I thought you weren't supposed to use that with the suppressor.....but it is there for a reason.
My other one stays tight w/o using the wave washer but it has a bunch of holes in the endcap for a spanner wrench and is smaller diameter.
My other one stays tight w/o using the wave washer but it has a bunch of holes in the endcap for a spanner wrench and is smaller diameter.
--------------------------------------
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
-
- Senior Silent Operator
- Posts: 126
- Joined: Thu Aug 29, 2013 5:56 pm
- Location: South South Texas
Re: Endcap won't stay tight
2 small spring loaded grub screws on suppressor side to match up with spanner holes on the 22/45 lite should keep it from rotating loose.
Another option notice threads on the 22/45 lite are not threaded all the way to the base ?
Machine out a beveled space in the suppressor for a small o-ring to compress within the space that is not threaded on the barrel when mated together.
Not sure if this makes sense the way I explained it.
Another option notice threads on the 22/45 lite are not threaded all the way to the base ?
Machine out a beveled space in the suppressor for a small o-ring to compress within the space that is not threaded on the barrel when mated together.
Not sure if this makes sense the way I explained it.
NRA Life Member
- mpallett
- Elite Industry Professional
- Posts: 2876
- Joined: Mon Apr 25, 2005 9:28 am
- Location: MA
- Contact:
Re: Endcap won't stay tight
The suppressor mount threads look off. (could be the picture)
Over weight Telco guy with a FFL/07 for hire
Re: Endcap won't stay tight
[quote="mpallett"]The suppressor mount threads look off. (could be the picture)[/quo
On the gun or silencer? Gun is factory, silencer endcap are good 1/2-28
On the gun or silencer? Gun is factory, silencer endcap are good 1/2-28
--------------------------------------
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me