223 K baffles?
- mattman0o0o
- Member
- Posts: 41
- Joined: Mon Dec 06, 2010 5:50 pm
- Location: Kansas
223 K baffles?
Anyone done this? If so wouldn't they have to be beefier around the cone/disk joint area?
.22 form 1 - http://youtu.be/grDBBcMjacI
.22 form 1 build thread - http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79544
.22 form 1 build thread - http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79544
- T-Rex
- Silent But Deadly
- Posts: 1865
- Joined: Wed Oct 29, 2014 3:38 pm
- Location: CT - The AntiConstitution State
Re: 223 K baffles?
The good Capt. has provided information on K's being used on centerfire rifle rounds.
I'd hate to misquote him so I'd suggest a site search w/ the correct parameters.
My recollection has them being a useful albeit tedious design.
You'd yield the greatest results through testing, but this isn't available to US Form 1 builders.
Any particular reason you're querying this route?
I'd hate to misquote him so I'd suggest a site search w/ the correct parameters.
My recollection has them being a useful albeit tedious design.
You'd yield the greatest results through testing, but this isn't available to US Form 1 builders.
Any particular reason you're querying this route?
Completed Builds www.silencertalk.com/forum/viewtopic.php?t=79895
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Re: 223 K baffles?
joe curtis of curtis tactical claims his k baffles are equally effective as his cones in .308, so it might be possible to optimize a .223 k can.
300 blackout form 1: http://www.silencertalk.com/forum/viewtopic.php?f=10&t=137293
5.56 form 1:
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=141800&p=955647#p955647
5.56 form 1:
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=141800&p=955647#p955647
- Capt. Link.
- Silent But Deadly
- Posts: 2829
- Joined: Wed Oct 17, 2007 9:05 pm
- Location: USA.
Re: 223 K baffles?
K baffles need to be reinforced at the edge for centerfire.AWC did this by welding.I have done this by threading the interior of the suppressor and screwing each baffle in place.I like the sound a K baffle has over other designs but you must put more work into them over ported cone types.
-CL
-CL
The only reason after 243 years the government now wants to disarm you is they intend to do something you would shoot them for!
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
- mattman0o0o
- Member
- Posts: 41
- Joined: Mon Dec 06, 2010 5:50 pm
- Location: Kansas
Re: 223 K baffles?
I only reason I asked was I remembered seeing it in the past but couldn't locate where. Most likely the Capt's post. Welding and threading the tube sounds like it might be too much work for me.
.22 form 1 - http://youtu.be/grDBBcMjacI
.22 form 1 build thread - http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79544
.22 form 1 build thread - http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79544
Re: 223 K baffles?
I did mine as a mix of K's & cones - for no good reason other than I wanted to see what happened. It's ok. Not an SPR or NT-4, but it's decent.
You can search the completed build thread for it. I think I put some pics of the K's up.
You can search the completed build thread for it. I think I put some pics of the K's up.
--------------------------------------
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me
"Sorry but you cannot use search at this time. Please try again in a few minutes"
"This board is currently disabled"
These things make me