Sound Suppressor Discussion
It is currently Tue Dec 18, 2018 12:44 pm

All times are UTC-04:00

Post new topic  Reply to topic  [ 2 posts ] 
Author Message
PostPosted: Wed Sep 06, 2017 7:40 am 
New Member

Joined: Wed Sep 06, 2017 5:33 am
Posts: 2
I own a GemTech Tundra 9mm suppressor that I am interested in using with an HK style 3-lug mount. This will be on a 9mm AR, semi-auto only.

To do this, I need to find a compatible 3-lug mount. I've seen several references to the AAC 3-lug adapter being compatible. However, I've been unsuccessful in finding information from anyone who has actually used this configuration. I contacted AAC and they declined to commend on compatibility of their components on the Gemtech unit. That's understandable and what I expected them to say, but I had to ask.

I think another option may be GemTech's 3-lug mount for their Multimount can. The Tundra and the Multimount appear to be very similar. The Multimount L.I.D. looks like the Tundra's to me. Unfortunately, I've seen no references to the MM adapters working on the Tundra. I contacted GemTech and they told me that the Tundra's L.I.D. is permanently attached and its configuration can't be changed.

To muddy the water, however, I found this post from user Captdreifus in which he posts a photo of his Tundra disassembled, with the L.I.D. body removed. The thread is about jailbreaking, but he does not mention doing anything unusual to get his Tundra taken down to this state.


I'd appreciate anyone's advice on how to remove the L.I.D. body from my Tundra.

I'd also appreciate any information on users' experience with GemTech or third party 3-lug adapters that may work with my Tundra.



BulletFlight for Android
PostPosted: Thu Sep 07, 2017 4:39 am 
New Member

Joined: Wed Sep 06, 2017 5:33 am
Posts: 2
Some images to better show what I'm asking in the previous post:

My GemTech Tundra with L.I.D. attached:

Close view of the exterior of the Tundra L.I.D.:

This is the interior of the Tundra L.I.D. When taking these photos, I noticed the nubbin toward the bottom that is circled. I suspect this may be a pin or screw keeping the L.I.D. in place.

This is a reference photo of the GemTech Multimount L.I.D. booster. It appears to be the same as the unit on my Tundra. I've never had access to one, so I can't verify dimensions, thread size, etc.

I have now tried to gently heat up the suppressor to loosen any possible thread locker. Even when it's very hot, no amount of manual torque I can put onto it will loosen the L.I.D. If it's thread locker holding it on, it's the high temperature variety.

Now I'm wondering if the pin/screw in the above picture can be removed without damaging the suppressor. And if so, if that will that allow me to get the L.I.D. off. I'd appreciate any suggestions on a procedure and tools required to do that.

Of course, I still don't know if there is a 3-lug mount that'll work on the Tundra once I get the L.I.D. off of it.

Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 2 posts ] 

All times are UTC-04:00

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Powered by phpBB® Forum Software © phpBB Limited
[ GZIP: Off | Load: 0.67 ]