Anyone confirmed if pitch dia. is truly incorrect on drawing. I'm having a barrel cut also.
Silencerco rep., any response???
Drawing with incorrect pitch dia.???
Moderators: Kenny_SilencerCo, Andrew@Silencerco
Re: Drawing with incorrect pitch dia.???
Hello, pitch diameter?
-
- Member
- Posts: 29
- Joined: Wed May 12, 2010 6:19 pm
Re: Drawing with incorrect pitch dia.???
On????????????????????????
- Kenny_SilencerCo
- Silent But Deadly
- Posts: 483
- Joined: Wed Sep 01, 2010 10:19 am
Re: Drawing with incorrect pitch dia.???
Conaso wrote:Anyone confirmed if pitch dia. is truly incorrect on drawing. I'm having a barrel cut also.
Silencerco rep., any response???
Hey sorry about the late response!
I just checked and it IS NOT the correct drawing. We are working on getting the correct PDF up on our web site. I will let you know as soon as it goes up.
Thanks for you patience.
Kenny Bozich
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
Re: Drawing with incorrect pitch dia.???
Holy s--t. I printed off the thread specs from the web site and included them with my barrel when I sent it off for threading.
It's been threaded and I just shipped it to Ident for engraving. Before I sent it out to be engraved I stopped by my Dealer and threaded my SS Sparrow onto the barrel. It looked and fit OK.
Any advice?
It's been threaded and I just shipped it to Ident for engraving. Before I sent it out to be engraved I stopped by my Dealer and threaded my SS Sparrow onto the barrel. It looked and fit OK.
Any advice?
Give a man a gun and he can rob a bank.
Give a man a bank and he can rob the entire world.
Give a man a bank and he can rob the entire world.
Re: Drawing with incorrect pitch dia.???
I am in almost the same boat. I took a copy of the drawing off of the website to the Smith I am having do the work for me on two barrels. He has had my stuff for two weeks now, and I am hoping I can catch him before he gets to my barrels (if its not too late)DesertRat wrote:Holy s--t. I printed off the thread specs from the web site and included them with my barrel when I sent it off for threading.
It's been threaded and I just shipped it to Ident for engraving. Before I sent it out to be engraved I stopped by my Dealer and threaded my SS Sparrow onto the barrel. It looked and fit OK.
Any advice?
What would this cause if they are already threaded? Will the threads not engage as much as they should, and increase the chances of stripping the threads out?
Thanks
Silence is golden, Duct tape is silver
Re: Drawing with incorrect pitch dia.???
Holy crap..I just send me Ruger Mark III hunter to http://jpgrips.com/page5, and note to use http://www.22sparrow.com/?page=Specs, What is the correct specs for the threaded? Need to know A.S.A.P.
- Kenny_SilencerCo
- Silent But Deadly
- Posts: 483
- Joined: Wed Sep 01, 2010 10:19 am
Re: Drawing with incorrect pitch dia.???
I have the correct drawing. What are your emails so I can send the drawings to you?
Kenny Bozich
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
- Kenny_SilencerCo
- Silent But Deadly
- Posts: 483
- Joined: Wed Sep 01, 2010 10:19 am
Re: Drawing with incorrect pitch dia.???
Some of the numbers on the bad drawing were switched on accident. Any experienced machinist would have caught this mistake. Sorry about the mixup.
Kenny Bozich
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
Re: Drawing with incorrect pitch dia.???
Please send new drawing soonest... [email protected] [email protected]
- Kenny_SilencerCo
- Silent But Deadly
- Posts: 483
- Joined: Wed Sep 01, 2010 10:19 am
Re: Drawing with incorrect pitch dia.???
Conaso wrote:Please send new drawing soonest... [email protected] [email protected]
Just sent it to both emails
Kenny Bozich
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
SILENCERCO
Social Media Director
[email protected]
www.silencerco.com
5511 South 6055 West
West Valley City, UT 84118
(801) 417-5384 o
(801) 417-5002 f
Re: Drawing with incorrect pitch dia.???
Compared the drawing you emailed to me to the drawing that I downloaded from the website and they are identical. Guess that explains why the Sparrow screwed onto my barrel without any issues.
Thanks for the response. My Form 4 should be in my dealer's hands sometime in the next few weeks. Can't wait.
Thanks for the response. My Form 4 should be in my dealer's hands sometime in the next few weeks. Can't wait.
Give a man a gun and he can rob a bank.
Give a man a bank and he can rob the entire world.
Give a man a bank and he can rob the entire world.