AAC 762SD

Company specific discussions and announcements.

Moderator: SilentMike

Post Reply
Jetmd
Member
Posts: 13
Joined: Sun Aug 02, 2009 12:39 pm

AAC 762SD

Post by Jetmd »

Can I safely run my 762SD on my 7mm WSM?
I would like to get a first-hand response from one of our AAC reps.
Thanks for your time!
sarthree
Senior Silent Operator
Posts: 112
Joined: Sun Aug 02, 2009 7:28 am

Re: AAC 762SD

Post by sarthree »

I'm not a suppressor master...but I'm going to say no. The 7mm's pressure (4100 J) is a lot higher than a 308's (3600 J) which is usually the tell tale sign of no.
Jetmd
Member
Posts: 13
Joined: Sun Aug 02, 2009 12:39 pm

Re: AAC 762SD

Post by Jetmd »

I agree with your post, but I am hoping to get a Yes or No answer from an AAC rep.
I am good with either answer directly from AAC, and If it is No I will just buy another
can.....this one rated for my 7mm WSM.
Thanks for your response.
User avatar
JasonM
Silent But Deadly
Posts: 1483
Joined: Sat Jul 16, 2011 2:51 pm
Location: NoVA
Contact:

Re: AAC 762SD

Post by JasonM »

Jetmd wrote:I agree with your post, but I am hoping to get a Yes or No answer from an AAC rep.
I am good with either answer directly from AAC, and If it is No I will just buy another
can.....this one rated for my 7mm WSM.
Thanks for your response.
They aren't always on the forum, you'll get a direct answer guaranteed only by asking them directly-

try [email protected]
[email protected]
[email protected]
or [email protected]
Kick Ass Design
ten:pm media
www.facebook.com/VisualGravy
cpatterson86
Silent Operator
Posts: 54
Joined: Thu May 24, 2012 10:06 am
Location: GA

Re: AAC 762SD

Post by cpatterson86 »

Jetmd wrote:Can I safely run my 762SD on my 7mm WSM?
I would like to get a first-hand response from one of our AAC reps.
Thanks for your time!
Sorry, but it is not rated for that caliber.
Jetmd
Member
Posts: 13
Joined: Sun Aug 02, 2009 12:39 pm

Re: AAC 762SD

Post by Jetmd »

Thank-you for your response!
That is all I needed to know.
Tater_ga
Silent Operator
Posts: 56
Joined: Thu May 24, 2012 11:46 am

Re: AAC 762SD

Post by Tater_ga »

sarthree wrote:I'm not a suppressor master...but I'm going to say no. The 7mm's pressure (4100 J) is a lot higher than a 308's (3600 J) which is usually the tell tale sign of no.
Smart answer. Hopefully the below info will help out with future questions.

You can use a silencer on an alternate caliber as long as the projectile diameter and pressure are equal to or less than the caliber the silencer was designed for. You can use 5.56mm in a silencer designed for 7.62mm, but you should not use a 300 Ultra Mag round in a 7.62mm silencer. Stay with equal or less case capacity than the silencer was designed for. Using a silencer in an alternate caliber can be fun and cost effective, if you use common sense and stay within these guidelines.

This link shows a pretty good list of case capacities for most modern cartridges.
http://kwk.us/cases.html
Brent

Certified Silencer Nerd


Semper Fidelis (2005-2010)
sarthree
Senior Silent Operator
Posts: 112
Joined: Sun Aug 02, 2009 7:28 am

Re: AAC 762SD

Post by sarthree »

Tater_ga wrote:
sarthree wrote:I'm not a suppressor master...but I'm going to say no. The 7mm's pressure (4100 J) is a lot higher than a 308's (3600 J) which is usually the tell tale sign of no.
Smart answer. Hopefully the below info will help out with future questions.
Gracias
Post Reply