762-SDN-6

Company specific discussions and announcements.

Moderator: SilentMike

brazos609
Silent But Deadly
Posts: 383
Joined: Sun May 29, 2005 11:12 am
Location: TX

762-SDN-6

Post by brazos609 » Thu Sep 30, 2010 2:09 pm

Might as well go ahead and start the thread or ten more people will. I am guessing it a a shorter version of the 762-SD optimized for subsonic rounds? The question everyone will ask will be, when will it be available.

seattlite
Silent But Deadly
Posts: 322
Joined: Tue Mar 24, 2009 10:17 pm
Location: PNW

Re: 762-SDN-6

Post by seattlite » Thu Sep 30, 2010 4:05 pm


User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Thu Sep 30, 2010 5:27 pm

It is an awesome can.

It performs very well with 300BLK, and does a damn good job with 5.56 too. I like it.

Image

Image
Kick Ass Design

the_accuser
Silent But Deadly
Posts: 242
Joined: Sun Mar 12, 2006 11:04 pm
Location: Nashville, TN

Re: 762-SDN-6

Post by the_accuser » Thu Sep 30, 2010 9:28 pm

Hey Jason, I just bought a Noveske 12.5" crusader with the AAC blackout flash hider in 5.56 caliber. Will the new 762-SDN-6 can work with that setup or am I better off just sticking with the M4-2000?

Thanks,
Jason
Last edited by the_accuser on Fri Oct 01, 2010 8:43 am, edited 1 time in total.

User avatar
Twinsen
Silent But Deadly
Posts: 7693
Joined: Tue Sep 04, 2007 11:34 pm
Location: AZ

Re: 762-SDN-6

Post by Twinsen » Fri Oct 01, 2010 3:14 am

CycloneK : Cyclone
762-SDN-6 : 762SD ?

LonghunterCO
Silent But Deadly
Posts: 391
Joined: Tue Dec 23, 2008 10:27 pm
Location: Snowy Colorado

Re: 762-SDN-6

Post by LonghunterCO » Fri Oct 01, 2010 11:45 am

So this is a lighter weight/shorter length/ lower Db reducing version of the 762SD?

brazos609
Silent But Deadly
Posts: 383
Joined: Sun May 29, 2005 11:12 am
Location: TX

Re: 762-SDN-6

Post by brazos609 » Fri Oct 01, 2010 12:26 pm

LonghunterCO wrote:So this is a lighter weight/shorter length/ lower Db reducing version of the 762SD?
Shorter but a little heavier it seems.

User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Fri Oct 01, 2010 12:31 pm

the_accuser wrote:Hey Jason, I just bought a Noveske 12.5" crusader with the AAC blackout flash hider in 5.56 caliber. Will the new 762-SDN-6 can work with that setup or am I better off just sticking with the M4-2000?

Thanks,
Jason

If you intend to stay 5.56, the m4-2000 will be a better performer. If you want a multi-caliber can, the 762-SDN-6 does pretty darn well with 5.56.
Kick Ass Design

st33ve0
Silent But Deadly
Posts: 3864
Joined: Sun Apr 06, 2008 8:47 am
Location: Chattanooga, TN
Contact:

Re: 762-SDN-6

Post by st33ve0 » Fri Oct 01, 2010 1:56 pm

So is the 762-SDN-6 not rated for 7.62x51?

User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Fri Oct 01, 2010 2:04 pm

st33ve0 wrote:So is the 762-SDN-6 not rated for 7.62x51?
Sorry for any confusion Steve, yes, the 762-SDN-6 is rated for 7.62x51/.308 Nato. And it's a damn good performer too.
Kick Ass Design

st33ve0
Silent But Deadly
Posts: 3864
Joined: Sun Apr 06, 2008 8:47 am
Location: Chattanooga, TN
Contact:

Re: 762-SDN-6

Post by st33ve0 » Fri Oct 01, 2010 7:51 pm

JasonAAC wrote:
st33ve0 wrote:So is the 762-SDN-6 not rated for 7.62x51?
Sorry for any confusion Steve, yes, the 762-SDN-6 is rated for 7.62x51/.308 Nato. And it's a damn good performer too.
Cool, thanks for answering our deluge of questions Jason :D

User avatar
Stickman
Silent But Deadly
Posts: 1136
Joined: Thu Nov 01, 2007 11:14 pm

Re: 762-SDN-6

Post by Stickman » Sat Oct 02, 2010 12:34 pm

Image
Stick

I've done work photography work with 45 or so manufacturers within the firearm community, my images have been used for catalogs, magazines, covers, etc. I have also shot work for the US Military. I am prior service and a full time LEO.

I now also shoot and write for Military Times. My primary focus will stay with weapons, accessories and related equipment reviews. Manufacturers can reach me through any of the boards. Have something new? Let me know.

http://www.flickr.com/photos/stickgunner

User avatar
firefighter509
Silent But Deadly
Posts: 363
Joined: Tue Jan 13, 2009 4:33 am

Re: 762-SDN-6

Post by firefighter509 » Sat Oct 02, 2010 4:41 pm

I just contacted my dealer about this, I am looking at building a suppressed gun for hunting. That can looks like its exactly what I want. DAMN YOU AAC DAMN YOU!!!!
So what the skinny, when we going to be able to buy these things ?
I MAY DIE IN A DITCH, BUT I WILL BE LYING IN A BED OF BRASS!
LIKE REGAN WATCH THIS:
http://www.youtube.com/watch?v=49zqB6qV7hI&feature=related

M1AJUNKIE
Member
Posts: 42
Joined: Tue May 18, 2010 9:32 pm

Re: 762-SDN-6

Post by M1AJUNKIE » Sat Oct 02, 2010 4:53 pm

What are the differences between the 762SDN and the regular 762SD? I am looking into a multicalber can for both .308 and .223 and was set on the 762SD. Now that the 762SDN is out, which can would be a better choice for me? The can will be used on 1 16" .223, 1 20" .223 and an LMT MWS.

User avatar
SilentMike
Silent But Deadly
Posts: 597
Joined: Mon May 02, 2005 12:57 pm
Location: Alpharetta, GA

Re: 762-SDN-6

Post by SilentMike » Sat Oct 02, 2010 7:39 pm

The 762SD is 9.1" OAL and weighs a little more than 19 ounces. It has eight baffles. The 762SDN is 7.7" OAL and weighs the same as the full sized 762SD because it has 9 baffles. The baffles used in the 762SDN are quite a bit different from those in the 762SD. One of the design goals with the 762SDN was to make the suppressor as tranparent to the host firearm as possible. We suceeded in minimizing cyclic rate and bolt velocity increase, which has the side benefit of less gas in the shooters face.

We recently metered the 762SDN on a 16" 5.56mm AR and got right around 136 dB metering mil-spec at one meter to the left.
Mike Smith
Advanced Armament Corp.
770-925-9988

User avatar
Ctaylor
Silent But Deadly
Posts: 535
Joined: Wed Feb 03, 2010 12:14 am
Location: Atlanta, GA
Contact:

Re: 762-SDN-6

Post by Ctaylor » Sun Oct 03, 2010 12:08 am

SilentMike wrote:The 762SD is 9.1" OAL and weighs a little more than 19 ounces. It has eight baffles. The 762SDN is 7.7" OAL and weighs the same as the full sized 762SD because it has 9 baffles. The baffles used in the 762SDN are quite a bit different from those in the 762SD. One of the design goals with the 762SDN was to make the suppressor as tranparent to the host firearm as possible. We suceeded in minimizing cyclic rate and bolt velocity increase, which has the side benefit of less gas in the shooters face.

We recently metered the 762SDN on a 16" AR and got right around 136 dB metering mil-spec at one meter to the left.
Image

dmtsc
Silent But Deadly
Posts: 310
Joined: Sat Mar 18, 2006 8:04 pm
Location: Virginia

Re: 762-SDN-6

Post by dmtsc » Sun Oct 03, 2010 9:42 am

Have you guys shot this can on a 6.8SPC? Will this can mount on the mounts for the M4-2000?
AAC 762SD, EVO 9 ,PILOT. Gemtech M4-96D, OutbackII, Ops Inc 12th, Ops Inc 3rd Model, Multimount and 2 TBA Mk2 integrals. Ops Inc. M4-s, Gemtech Mk9-k on the way for MP5K, KAC MP5SD can coming also

User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Sun Oct 03, 2010 10:24 am

dmtsc wrote:Have you guys shot this can on a 6.8SPC? Will this can mount on the mounts for the M4-2000?
Don't know on the 68, but yes to the m4-2000 mount. the 762-SDN-6 will work on any 51T Ratchet mount.
Kick Ass Design

LonghunterCO
Silent But Deadly
Posts: 391
Joined: Tue Dec 23, 2008 10:27 pm
Location: Snowy Colorado

Re: 762-SDN-6

Post by LonghunterCO » Sun Oct 03, 2010 11:01 am

JasonAAC wrote:
dmtsc wrote:Have you guys shot this can on a 6.8SPC? Will this can mount on the mounts for the M4-2000?
Don't know on the 68, but yes to the m4-2000 mount. the 762-SDN-6 will work on any 51T Ratchet mount.
So for the slow guy in the corrner that just had the light bulb come on above his head: The M4-2000 mount is now compatable with the 762-SDN-6, the M4-2000, and the 762SD (new style 51T)?

User avatar
SilentMike
Silent But Deadly
Posts: 597
Joined: Mon May 02, 2005 12:57 pm
Location: Alpharetta, GA

Re: 762-SDN-6

Post by SilentMike » Sun Oct 03, 2010 11:07 am

LonghunterCO wrote:
JasonAAC wrote:
dmtsc wrote:Have you guys shot this can on a 6.8SPC? Will this can mount on the mounts for the M4-2000?
Don't know on the 68, but yes to the m4-2000 mount. the 762-SDN-6 will work on any 51T Ratchet mount.
So for the slow guy in the corrner that just had the light bulb come on above his head: The M4-2000 mount is now compatable with the 762-SDN-6, the M4-2000, and the 762SD (new style 51T)?
Correct. The M4-2000, 762-SD, and 762-SDN-6 all share common mounting architecture.
Mike Smith
Advanced Armament Corp.
770-925-9988

User avatar
tcba_joe
Silent But Deadly
Posts: 151
Joined: Thu Aug 07, 2008 1:03 am

Re: 762-SDN-6

Post by tcba_joe » Sun Oct 03, 2010 5:22 pm

So if I wanted to suppress 5.56, 7.62NATO/.308, .300BLK and 7.62x39 this would be THE can to get?

While I only have 5.56 right now, I would like to get the others and would like to have to pay for as little in taxes as I can.

What's the projected price?

User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Sun Oct 03, 2010 5:37 pm

tcba_joe wrote:So if I wanted to suppress 5.56, 7.62NATO/.308, .300BLK and 7.62x39 this would be THE can to get?

While I only have 5.56 right now, I would like to get the others and would like to have to pay for as little in taxes as I can.

What's the projected price?
Yes.

Price same as the M4-2000. info on second page of this PDF: http://300aacblackout.com/resources/300 ... osheet.pdf
Kick Ass Design

seattlite
Silent But Deadly
Posts: 322
Joined: Tue Mar 24, 2009 10:17 pm
Location: PNW

Re: 762-SDN-6

Post by seattlite » Sun Oct 03, 2010 9:12 pm

Dang...I wish I knew about this can a week ago...I just bought a 51T 762-SD(Form 4 was sent to the BATF last last Wed). I really like the reduced length of the can....oh well.

User avatar
JasonAAC
Industry Professional
Posts: 2993
Joined: Thu Jul 02, 2009 4:08 pm
Location: VA
Contact:

Re: 762-SDN-6

Post by JasonAAC » Sun Oct 03, 2010 9:39 pm

seattlite wrote:Dang...I wish I knew about this can a week ago...I just bought a 51T 762-SD(Form 4 was sent to the BATF last last Wed). I really like the reduced length of the can....oh well.
51T 762-SD is an awesome can. And you'll have your can in hand by the time these are widely available at dealers.
Kick Ass Design

M1AJUNKIE
Member
Posts: 42
Joined: Tue May 18, 2010 9:32 pm

Re: 762-SDN-6

Post by M1AJUNKIE » Sun Oct 03, 2010 9:43 pm

JasonAAC wrote:
seattlite wrote:Dang...I wish I knew about this can a week ago...I just bought a 51T 762-SD(Form 4 was sent to the BATF last last Wed). I really like the reduced length of the can....oh well.
51T 762-SD is an awesome can. And you'll have your can in hand by the time these are widely available at dealers.

Will these new 762SDN's be available before shot show?

From the number in the pdf it appears the 762SDN is about 4 db's louder on the 7.62x 51 than the regular 762SD, is this a noticable difference? Would this can be hearing safe in an outdoor enviroment?

Any numbers on the db reduction when using this 762sdn on a 5.56mm rifle?

Post Reply