If you have a Scarab that you are having modified to take apart, why would you buy another stainless take apart can?
The advantage I see in aluminum cans is the lower weight so, I'm leaning towards an Aviator as a complement to my Scarab. If I don't shoot full-auto 22lr, I think by the time I need to clean out an Aviator by replacing it, the 50% cost of a retail upgrade which will run me ~$225 is insignificant compared to the cost of all the shooting I did to get to that point.
Of course, I could also get an SWR Warlock and take advantage of what I perceive to be a better service policy on a can that is full of lead. Again, since I don't shoot full-auto 22lr that feature isn't as significant to me personally for pure suppressor function reasons. Great customer service and customer support after the sale has some value all its own. SWR seems to have the edge in this specific scenario.
Personally, I think I will enjoy shooting my Scarab for a long time. When it is full and needs a cleaning I can't do with it sealed up, then I will either pay the %50 fee to AAC or, I will have it modified to become a take apart can.
Prodigy or Quest
Moderators: mpallett, mr fixit, bakerjw, renegade
- silencertalk
- Site Admin
- Posts: 33978
- Joined: Mon Apr 25, 2005 8:31 am
- Location: USA
The Scarab was my first and only 22 can, and it gets shared on a lot of host. I would probably get another if it was still available.Sid Post wrote:If you have a Scarab that you are having modified to take apart, why would you buy another stainless take apart can?
The advantage I see in aluminum cans is the lower weight so, I'm leaning towards an Aviator as a complement to my Scarab.
Of course, I could also get an SWR Warlock and take advantage of what I perceive to be a better service policy on a can that is full of lead.
Personally, I think I will enjoy shooting my Scarab for a long time. When it is full and needs a cleaning I can't do with it sealed up, then I will either pay the %50 fee to AAC or, I will have it modified to become a take apart can.
The weight is a non issue for me. I actually like having the extra weight with some setups, like the Glock 19 with the AA conversion kit. Fully loaded, the whole setup only weighs 16.6 oz. The Scarb adds some much needed heft and make it feel more like shooting the G19 with Evo9 attached.
SWR does have the reputation of fantastic customer service, but they do charge a fee ($65?) for cleaning after the initial return which is free. However companies and policies change, and I would rather be able to do the cleaning safely myself rather than have to mail it off and wait...
I wouldn't wait till it was filled up to get it modified - it might be impossible to get the baffle stack out then. I've added about an ounce to my scarab after several bricks of ammo, and I plan to send it off very soon. I was keeping track for a while on the weight increase - I believe it was on track to gain an ounce after 3-5k rounds of Rem golden bullet bulk packs. One big plus of the prodigy is the tapered tube...if only it was stainless. My ideal would have been a serial numbered stainless core with a carbon fiber tube but it seems the ATF wouldn't go along=( I believe AAC made a few stainless versions of the prodigy for testing last year and I made Keven an offer on one of those but never heard back.
That's a good thought to keep in mind. With all the welding AAC does these days, I figured that most cases would involve making a new can with the old information.rsilvers wrote:Remember that AAC's policy of 50% of retail is WORST case (such as if you destroy it on purpose and smash it with a sledge hammer). They often charge much less. Other companies worst case is FULL RETAIL. So remember not to compare worse-case from AAC with best-case from other companies.
Screw together cans would be easier to make simple fixes on for things like a baffle strike or cleaning before the 22lr can welds itself together. I like the AAC cans though because they do in fact weld things together for a lighter weight and very robust suppressor.
- silencertalk
- Site Admin
- Posts: 33978
- Joined: Mon Apr 25, 2005 8:31 am
- Location: USA
AAC can mill off a front end cap and weld a new one on. It is no more difficult for them to do that than it would be for most silencers.Sid Post wrote:That's a good thought to keep in mind. With all the welding AAC does these days, I figured that most cases would involve making a new can with the old information.rsilvers wrote:Remember that AAC's policy of 50% of retail is WORST case (such as if you destroy it on purpose and smash it with a sledge hammer). They often charge much less. Other companies worst case is FULL RETAIL. So remember not to compare worse-case from AAC with best-case from other companies.
Screw together cans would be easier to make simple fixes on for things like a baffle strike or cleaning before the 22lr can welds itself together. I like the AAC cans though because they do in fact weld things together for a lighter weight and very robust suppressor.
SRT integral
As far as suppressors that you can disassemble, does the integral SRT Arms Buckmark or Ruger integral count? I heard that you can remove the suppressor for cleaning. Anyone with an SRT integrral, can the suppressor can be taken off the bbl and allow cleaning of the chamber area? Pics of disassembly please?
Not totally on topic, but I thought it worth mentioning considering sealed cans came up, as well as AAC's warranty policy of up to 50% worst case. I sent an e-mail to Gemtech just for schitzengiggles in regards to their policy for sending in an Outback full of lead. This is verbatim from the e-mail I received back.
<i>1) We charge $150.00 for our rebuild service. We remove your old baffle stack and replace it with a brand new set of internals. While overall service life can vary widely depending on the type and frequency of shooting you do, a rebuild should not be necessary before 20,000 rounds. We have Outback-II units that have gone between 20,000 and 50,000 rounds before requiring rebuild. Although they were pretty full of lead build-up at that point, when metered we found they were still hearing safe.</i>
What's AAC's policy regarding this type of stuff? Do they replace all internals as well? What kind of fee do they charge for their sealed cans? I would imagine that the 50% deal would definitely not apply as cleaning out a can is no where near worst case scenario. Not trying to start anything, just thought maybe someone else would like the details too.
<i>1) We charge $150.00 for our rebuild service. We remove your old baffle stack and replace it with a brand new set of internals. While overall service life can vary widely depending on the type and frequency of shooting you do, a rebuild should not be necessary before 20,000 rounds. We have Outback-II units that have gone between 20,000 and 50,000 rounds before requiring rebuild. Although they were pretty full of lead build-up at that point, when metered we found they were still hearing safe.</i>
What's AAC's policy regarding this type of stuff? Do they replace all internals as well? What kind of fee do they charge for their sealed cans? I would imagine that the 50% deal would definitely not apply as cleaning out a can is no where near worst case scenario. Not trying to start anything, just thought maybe someone else would like the details too.
- silencertalk
- Site Admin
- Posts: 33978
- Joined: Mon Apr 25, 2005 8:31 am
- Location: USA
Hearing safe is 139.9dB and let me tell you that is VERY loud. Its louder than your average 223 can. "Hearing safe" is loud and on a filled up 22 can you might as well not have a can on, since is going to be almost a loud as without it.JohnnyC wrote:Not totally on topic, but I thought it worth mentioning considering sealed cans came up, as well as AAC's warranty policy of up to 50% worst case. I sent an e-mail to Gemtech just for schitzengiggles in regards to their policy for sending in an Outback full of lead. This is verbatim from the e-mail I received back.
<i>1) We charge $150.00 for our rebuild service. We remove your old baffle stack and replace it with a brand new set of internals. While overall service life can vary widely depending on the type and frequency of shooting you do, a rebuild should not be necessary before 20,000 rounds. We have Outback-II units that have gone between 20,000 and 50,000 rounds before requiring rebuild. Although they were pretty full of lead build-up at that point, when metered we found they were still hearing safe.</i>
What's AAC's policy regarding this type of stuff? Do they replace all internals as well? What kind of fee do they charge for their sealed cans? I would imagine that the 50% deal would definitely not apply as cleaning out a can is no where near worst case scenario. Not trying to start anything, just thought maybe someone else would like the details too.
07FFL 02 SOT
- silencertalk
- Site Admin
- Posts: 33978
- Joined: Mon Apr 25, 2005 8:31 am
- Location: USA
Re: Prodigy or Quest
The stainless Quest would look bad ass on my stainless Ruger MkII. I think that would be a sweet set up. Anyone shoot a Quest next to any other .22 cans? If so, how do they compare when it comes to sound reduction?
Very same reasoning I used when buying mine ...
Fair sound reduction (most shots,but it is erratic,some are LOUD) and has very nasty FRP
Very same reasoning I used when buying mine ...
Fair sound reduction (most shots,but it is erratic,some are LOUD) and has very nasty FRP
Re: Prodigy or Quest
I am sending my Quest to The Silencer Store for a rebuild.It is ok but nothing to brag about as far as sound reduction.I want it it as quiet as it can possibly be.
Re: Prodigy or Quest
I have two Quest cans, they are well made & work pretty well. They are quiet enough, but not in AAC league.
I paid a little over $200 a piece for them new, and they are definitely worth that. Still quiet enough for most people.
I do always use a little lithium grease in them on pistols. The FRP is pretty noticeable, too.
I paid a little over $200 a piece for them new, and they are definitely worth that. Still quiet enough for most people.
I do always use a little lithium grease in them on pistols. The FRP is pretty noticeable, too.
Re: Prodigy or Quest
I have a prodigy, with a Ruger mk3 22/45 as a host. Ridiculously quiet, easy to service (get aac's wrench set for the endcaps). It was my first can...and I don't see getting another 22 can unless I need a can for 22mag, 17hmr or the like.
Also, the prodigy is SUPER light! It really feels like nothing is on th end of the gun!
Highly recommend the prodigy, but I have only shot a few other 22 cans
Also, the prodigy is SUPER light! It really feels like nothing is on th end of the gun!
Highly recommend the prodigy, but I have only shot a few other 22 cans