Is .335+.005 too tight for the through bore for a 308 win muzzle brake?
I'm going to bore my baffles and end cap to .360+.005
My can is going on a FN SPR and it will be thread on 5/8x24
The barrel side end cap is going to have a built in muzzle brake to help with erosion, but being a bolt gun it's not going to see a lot of abuse
308 muzzle brake ?
-
- Senior Silent Operator
- Posts: 125
- Joined: Fri Jun 06, 2008 9:08 pm
Re: 308 muzzle brake ?
I use 0.350 for my 30 cal muzzle brakes. For baffles I use 0.365 - 0.375 progressively increased from the muzzle.
Re: 308 muzzle brake ?
>335 sounds mighty close. Better make sure that the bore is perfectly concentric with the threads and can when installed. Most people use .375 for the baffle holes. Some go as high as .390.
Re: 308 muzzle brake ?
I use 8 or 8.15mm all depending if it is for civilian or L&E / military use.
CNC in one operation, so things are in line.
This also differs if its a FH or MB. and length of course, but til today with 1000's of rounds never had a problem.
Gunny
CNC in one operation, so things are in line.
This also differs if its a FH or MB. and length of course, but til today with 1000's of rounds never had a problem.
Gunny
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=135514
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=77913
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=77913
Re: 308 muzzle brake ?
If you are having clearance problems 1.5" from the muzzle with a brake .030" over the bullet diameter, you have other serious issues that need to be corrected.
It's time to switch to whiskey, we've been drinkin' beer all night.
-
- Senior Silent Operator
- Posts: 125
- Joined: Fri Jun 06, 2008 9:08 pm
Re: 308 muzzle brake ?
It's concentric within the tolerances of my equipment and testing/measuring devices.
If I had to put a number on it within .005 probably closer but I don't have the equipment to test.
I am confident the pill will clear the hole without any chance of physical contact, I just wasn't sure if I needed to open it up some more to keep the gasses from disrupting flight or destabilizing it
If it matters, the plane of the brake is about 0.5" in front of the bore.
The rifle has about 0.75" of threads so the distance could be increased some if it would make an improvement.
If I had to put a number on it within .005 probably closer but I don't have the equipment to test.
I am confident the pill will clear the hole without any chance of physical contact, I just wasn't sure if I needed to open it up some more to keep the gasses from disrupting flight or destabilizing it
If it matters, the plane of the brake is about 0.5" in front of the bore.
The rifle has about 0.75" of threads so the distance could be increased some if it would make an improvement.
Re: 308 muzzle brake ?
I've just completed a 30 caliber can with 0.35" bore at the baffles. This is the minimum I'd dare go.
"There are no stupid questions, only stupid people". -MAJ MALFUNCTION
-
- Member
- Posts: 41
- Joined: Tue Jan 05, 2016 6:05 am
Re: 308 muzzle brake ?
Depending on how you can set it up will decide how tight you can go , I'd dialed barrels in off the ID of the bore and bored the brake to only .020" over bullet diameter and progressively reamed it at the range to see if the tighter bore showed any benefit in recoil reduction (it didn't).
Id suggest threading the 5/8x24 mount then cutting a 5/8x24 male stub in the lathe , screw the brake on the stub and bore the exit hole to desired ID , .350" is fine and will allow some room for error should you put the can on a barrel who's threads aren't perfect.
Id suggest threading the 5/8x24 mount then cutting a 5/8x24 male stub in the lathe , screw the brake on the stub and bore the exit hole to desired ID , .350" is fine and will allow some room for error should you put the can on a barrel who's threads aren't perfect.
-
- Senior Silent Operator
- Posts: 125
- Joined: Fri Jun 06, 2008 9:08 pm
Re: 308 muzzle brake ?
Pretty much exactly how I did it. I turned it out of 2" bar stock. Turned down to 1.75 to match the tube.Samson1044 wrote:Depending on how you can set it up will decide how tight you can go , I'd dialed barrels in off the ID of the bore and bored the brake to only .020" over bullet diameter and progressively reamed it at the range to see if the tighter bore showed any benefit in recoil reduction (it didn't).
Id suggest threading the 5/8x24 mount then cutting a 5/8x24 male stub in the lathe , screw the brake on the stub and bore the exit hole to desired ID , .350" is fine and will allow some room for error should you put the can on a barrel who's threads aren't perfect.
Turned down and threaded to mate to interior threads on the tube.
Then further turned down to .825 for the brake section and opened up through bore to .335
Next switched sides and adjusted in 4jaw to center. bored and threaded 5/8x24.
Threaded on rifle and marked horizon line for porting (not sure horizontal porting is necessary within the can but it looks good).
Still has to go into the mill to finish the porting and lightening (a lot of material left between the threads for the tube and the brake)