Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

General silencer discussion. If you want to talk about a specific silenced rifle or pistol, it is best to do that in the rifle or pistol section for that brand.

All NFA laws apply.

Moderators: mpallett, mr fixit, bakerjw, renegade

Post Reply
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

The Problem:

The Silencerco Octane/Omega 9K piston and fixed mounts are not compatible with conventional tools and cannot be adequately tightened or loosened by hand. In the case of the 13.5mmX1LH fixed and piston mounts, the barrel thread is left-handed and the suppressor body attaches to the mount with a right-hand thread. Rocksett can be used to solve this, but that makes frequent changing of the different mounts a challenge.

I recommend against doing a 3-lug mount arrangement (with the newer short mount, anyway), as the mechanism takes up blast chamber volume, which makes the suppressor considerably louder than with a direct-thread mount, which is what I recommend for the MPX. However, people usually say they use a 3-lug to prevent loosening of the suppressor from the weapon, which can happen with a direct-thread mount if adequate torque is not applied.

I would only use the piston system for pistols and not use a piston with a fixed barrel spacer on an MPX, as this arrangement is also louder than a direct thread mount, but you have no choice but to use a piston mount on a pistol.

The Solution:

I 3D modeled and printed a wrench that interfaces with the Octane/Omega 9K direct thread/piston mounts. Silencerco does not make a wrench for these. My wrench is a high-strength PLA polymer material that will break if way too much torque is applied, but if you torque it on with the wrench without a lot of Rocksett, it should torque back off without problems (a very small amount of Rocksett is fine). This wrench is critical for torqueing to the left onto the barrel and then for isolating the mount from the right-hand torque applied to install the suppressor body to the mount.

I can now easily transition between piston and fixed mounts for my Omega 9K.

I also did one for the Dead Air Wolf-9SD.

Image

Image

Image

Image

Image
Last edited by chase on Thu Jan 25, 2018 7:27 am, edited 1 time in total.
Chase

suppressortools.com
hyrulejedi86
Senior Silent Operator
Posts: 110
Joined: Mon Sep 03, 2012 11:39 am
Location: Cleveland, Oh area

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by hyrulejedi86 »

Well done! I designed and printed a tool a couple years ago for my Octane 9 but it was their old mount style that it fit. It makes a huge difference in trying to change mounts.
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Thank you!
Chase

suppressortools.com
User avatar
doubloon
Silent But Deadly
Posts: 11897
Joined: Wed Dec 31, 2008 11:02 pm
Location: Houston-ish

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by doubloon »

Very nice, good looking work.
http://www.youtube.com/watch?v=BDtd2jNIwAU MUSAFAR!
http://www.youtube.com/watch?v=8CrOL-ydFMI This is Water DavidW
Complete Form 1s http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
User avatar
fishman
Silent But Deadly
Posts: 1444
Joined: Sun Dec 20, 2015 7:15 pm

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by fishman »

I don't know why I've never thought to 3d print a tool for my form 1 endcap. I was gonna make an aluminum one but never got around to it.
300 blackout form 1: http://www.silencertalk.com/forum/viewtopic.php?f=10&t=137293

5.56 form 1:
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=141800&p=955647#p955647
savage54
Member
Posts: 32
Joined: Sat Oct 18, 2014 10:35 am

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by savage54 »

chase wrote:The Problem:

The Solution:

I 3D modeled and printed a wrench that interfaces with the Octane/Omega 9K direct thread/piston mounts. Silencerco does not make a wrench for these. My wrench is a high-strength PLA polymer material that will break if way too much torque is applied, but if you torque it on with the wrench without a lot of Rocksett, it should torque back off without problems (a very small amount of Rocksett is fine). This wrench is critical for torqueing to the left onto the barrel and then for isolating the mount from the right-hand torque applied to install the suppressor body to the mount.

I can now easily transition between piston and fixed mounts for my Omega 9K.
Are you interested in making a few more for sale? I know I can't be the only person who doesn't have a 3D printer.
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Check private messages.
savage54 wrote:
Are you interested in making a few more for sale? I know I can't be the only person who doesn't have a 3D printer.
Chase

suppressortools.com
DrDremel
Senior Silent Operator
Posts: 133
Joined: Mon Jan 02, 2006 6:10 pm
Location: Ortonville, MI

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by DrDremel »

Please sell these. I need them.
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Check private messages.
DrDremel wrote:Please sell these. I need them.
Chase

suppressortools.com
Bradpierson26
Silent Operator
Posts: 70
Joined: Sat Jan 24, 2015 9:28 am

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by Bradpierson26 »

I'd be interested in the Wolf wrench!
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Bradpierson26 wrote:I'd be interested in the Wolf wrench!
Check private messages.
Chase

suppressortools.com
User avatar
twodollarbill
Silent But Deadly
Posts: 420
Joined: Wed May 30, 2007 5:25 pm
Location: wisconsin

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by twodollarbill »

Awesome!
User avatar
Joshua@CapitolArmory
Senior Silent Operator
Posts: 120
Joined: Wed Feb 11, 2015 2:38 pm
Contact:

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by Joshua@CapitolArmory »

You can use an AR armorer's wrench for the Wolf (and Ghost). Pretend it's a castle nut and you're good to go.
Joshua

[email protected]
Capitol Armory
FFL/SOT
www.CapitolArmory.com
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Joshua@CapitolArmory wrote:You can use an AR armorer's wrench for the Wolf (and Ghost). Pretend it's a castle nut and you're good to go.
Correct, but the polymer wrench won't damage the mount's finish.
Chase

suppressortools.com
Oldfalguy
New Member
Posts: 1
Joined: Fri Jan 12, 2018 9:11 pm

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by Oldfalguy »

I too would be interested in a wrench too. Have not received my Wolf SD yet
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Oldfalguy wrote:I too would be interested in a wrench too. Have not received my Wolf SD yet
Private message sent.
Chase

suppressortools.com
buckgunner
Silent Operator
Posts: 80
Joined: Thu Jan 01, 2009 8:51 am

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by buckgunner »

I'm interested in a wrench for the Octane 45 HD.
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

buckgunner wrote:I'm interested in a wrench for the Octane 45 HD.
PM sent.
Chase

suppressortools.com
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

More are now available.
Chase

suppressortools.com
Kramer
Silent But Deadly
Posts: 1083
Joined: Sat Dec 20, 2008 3:13 pm
Location: nePA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by Kramer »

Interested in a wrench for my 45 Octane HD.
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

Kramer wrote:Interested in a wrench for my 45 Octane HD.
PM sent.
Chase

suppressortools.com
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

More are now available.
Chase

suppressortools.com
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

I just made a whole bunch more wrenches for Omega 9K/45K/Octane and Wolf 9SD/Ghost mounts.
Chase

suppressortools.com
bravo2
New Member
Posts: 1
Joined: Sun Nov 04, 2018 10:55 pm

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by bravo2 »

I got a omega 9k, ghost 45m, omega, hybrid among others coming. What you got and pics and price?
chase
Silent But Deadly
Posts: 162
Joined: Tue Dec 04, 2007 6:12 pm
Location: GA

Re: Omega 9K/45K/Octane Mount Wrench (And for Dead Air Wolf 9SD too!)

Post by chase »

bravo2 wrote:I got a omega 9k, ghost 45m, omega, hybrid among others coming. What you got and pics and price?
Here is the latest info:
https://tinyurl.com/WIT-LLC-Tools-10-06-2018-01

Video review:
https://youtu.be/fGXkqMGHrUA

Thanks!
Chase

suppressortools.com
Post Reply