https://i.imgur.com/XTvjtlh.png
https://i.imgur.com/cvSGJr7.png
1.5" OD, 8" long.
7 baffles (.24" bullet path), 3 wipes, and a pretty generously reinforced blast chamber.
It's designed to screw onto the end of my 9mm Form 1 can I'm building, to allow .22lr to be used with it. It will also screw directly onto that can's muzzle thread adapter, to be used as a standalone .22 can. By way of a coupler, all components and wipes can be assembled into one functioning can, so there are no "extra" bits, as it were.
Not much else to say about it. Probably print it out of nylon or polycarbonate. Just trying to decide if notching the baffles is a good idea or not. I've heard anecdotal reports that .22 cans benefit more from a tight fitting bullet path than from notching and such. Opinions on that would be welcome.
R8 my 3D printed Form1 design
- T-Rex
- Silent But Deadly
- Posts: 1865
- Joined: Wed Oct 29, 2014 3:38 pm
- Location: CT - The AntiConstitution State
Re: R8 my 3D printed Form1 design
Why build something that's easily machined?
Why are you using plastics? Need to be overly thick, wasting crucial volume.
Always clip baffles.
IMHO, it's a waste of a stamp. You're not doing anything that hasn't been done, it won't be an optimal design for 22lr, and it won't last as long as traditional materials.
Why are you using plastics? Need to be overly thick, wasting crucial volume.
Always clip baffles.
IMHO, it's a waste of a stamp. You're not doing anything that hasn't been done, it won't be an optimal design for 22lr, and it won't last as long as traditional materials.
Completed Builds www.silencertalk.com/forum/viewtopic.php?t=79895
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Re: R8 my 3D printed Form1 design
Your silencer has a silencer.
Being able to sat that alone is worth the $200.
Being able to sat that alone is worth the $200.
So much has changed since my last form 1
- Capt. Link.
- Silent But Deadly
- Posts: 2829
- Joined: Wed Oct 17, 2007 9:05 pm
- Location: USA.
Re: R8 my 3D printed Form1 design
A 8.00" suppressor with a .24 bore will cause all kinds of baffle strikes.okie_01 wrote: ↑Fri Jul 31, 2020 4:41 am https://i.imgur.com/XTvjtlh.png
https://i.imgur.com/cvSGJr7.png
1.5" OD, 8" long.
7 baffles (.24" bullet path), 3 wipes, and a pretty generously reinforced blast chamber.
Opinions on that would be welcome.
Wipes cause much inaccuracy plus you will need a FFL to replace them.
Not a good stamp investment as designed.
The only reason after 243 years the government now wants to disarm you is they intend to do something you would shoot them for!
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
-
- Silent Operator
- Posts: 99
- Joined: Wed Apr 27, 2016 7:37 pm
Re: R8 my 3D printed Form1 design
With a bullet diameter of .223 -.225 going down a bore of .240 for 8" your threading better be perfect. I would not run it that tight. Listen to the Captain.
- T-Rex
- Silent But Deadly
- Posts: 1865
- Joined: Wed Oct 29, 2014 3:38 pm
- Location: CT - The AntiConstitution State
Re: R8 my 3D printed Form1 design
I can't agree with this part.Capt. Link. wrote: ↑Sat Aug 01, 2020 10:45 am Wipes cause much inaccuracy plus you will need a FFL to replace them.
My 4.5" AR15/22, can hit 3.5" swingers @100yds, from a wiped can.
Also, the end user can legally replace wipes. ATF has never reversed this decision.
Completed Builds www.silencertalk.com/forum/viewtopic.php?t=79895
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
- Capt. Link.
- Silent But Deadly
- Posts: 2829
- Joined: Wed Oct 17, 2007 9:05 pm
- Location: USA.
Re: R8 my 3D printed Form1 design
Thank you as I thought wipes were under ATF regulation.T-Rex wrote: ↑Sun Aug 02, 2020 7:31 amI can't agree with this part.Capt. Link. wrote: ↑Sat Aug 01, 2020 10:45 am Wipes cause much inaccuracy plus you will need a FFL to replace them.
My 4.5" AR15/22, can hit 3.5" swingers @100yds, from a wiped can.
Also, the end user can legally replace wipes. ATF has never reversed this decision.
I'm happy you are getting good accuracy from your .22 AR-15. I have not had the same experience.My only exposure to wipes were in using the venerable WOX-1 aka Hush puppy. Rabbit sized prey had a 50/50 chance at 25yds though sound suppression was superb.The inaccuracy of that design has affected my taste for them
I'm guessing your can is a hybrid design that features baffles w/ a end wipe and not built like the WOX-1's stack ?
-CL
The only reason after 243 years the government now wants to disarm you is they intend to do something you would shoot them for!
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
http://www.silencertalk.com/forum/viewtopic.php?f=10&t=79895
- T-Rex
- Silent But Deadly
- Posts: 1865
- Joined: Wed Oct 29, 2014 3:38 pm
- Location: CT - The AntiConstitution State
Re: R8 my 3D printed Form1 design
I'd say you're right. I'm just wiped at the exit, not throughout.Capt. Link. wrote: ↑Mon Aug 03, 2020 2:52 pm I'm guessing your can is a hybrid design that features baffles w/ a end wipe and not built like the WOX-1's stack ?
-CL
Completed Builds www.silencertalk.com/forum/viewtopic.php?t=79895
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/
Burst Calculator www.engineersedge.com/calculators/pipe_bust_calc.htm
Silencer Porn www.instagram.com/explore/tags/silencerporn/